Pressure drop, a forgotten problem

 

Do you want maximum efficiency from your compressed air system? Pressure drop can be one of the reasons why you use too much compressed air and pay too high compressed air costs.

Pressure drop when blowing with compressed air is a common problem within the industry, but few know about it. A pressure drop is when there is a pressure difference between the air that leaves the compressor and the air that reaches the point-of-use. The point-of-use can for example be an air blow gun or an air knife. It is not unusual that the pressure has dropped 1 Bar (14.5 psi) before it reaches the final user. This can lead to lower product quality, impaired efficiency and higher compressed air costs.

What causes a pressure drop?

Pressure drop can occur due to a lot of different causes. One of the most common reasons are problems with the transportation of compressed air from the compressor to the point-of-use. Both the transportation length and the design of the transportation system affect the pressure drop. The pressure drops more the longer the compressed air is transported and depending on the amount of bends and curves on the pipes. It is also common that the pipe dimension gets thinner the longer you get from the compressor. To get the best result possible it should be the other way around. The pipe dimension should be wider the longer you get from the compressor. Then the pipe can also be used as a stock which will lower the risk of pressure drop.

Another common reason for pressure drop is bad maintenance and knowledge of filters and regulators. It is important to clean or switch the filters regularly and make sure that you use the right model of regulators to minimize the risk of pressure drop.

Why is it important to have knowledge about the problem with pressure drop? 

Pressure drop can cause a number of problems in the industry. It can for example have negative effect on the performance of pneumatic equipment, which can lead to other consequences.

If you do not have knowledge about the existence of pressure drop, and you experience that you do not get the expected effect, a common action is to raise the pressure in the compressor to reach the wanted effect at the point-of-use. But the pressure in the compressor is seldom the problem. Instead, an increased pressure tends to lead to unnecessary high use of energy, which increases the cost and damages components that do not manage the increased pressure.

It is because of this it is important to have knowledge about pressure drops and to measure the pressure continuously to be able to identify pressure differences, which can indicate problem in the system. An increased or decreased pressure means that something has changed, it can for example give an indication about there is a leak in the system or that a machine has stopped working. To measure pressure drops you can use a flowmeter. Why should you use a flowmeter?

Find out what your compressed air cost!   Read Silvent´s calculation recommendations here.

All posts

OSHA compliant air blow guns – avoid the Hearing Conservation Program

Read more
Silvent-man-with-helmet-noise

Quiet air blow guns with high blowing force

Read more
Steel application

How to safely clean away metal fluids by blowing with compressed air

Read more

What is a safe air blow gun?

Read more
Silvent-flowmeter

How to convert compressed air consumption from Nl/minute to Nm3/hour

Read more
silvent-nozzles-in-machine-darker

When should you replace air blow guns with air nozzles?

Read more
Kulventil3

Dangers with ball valves - use air blow guns with high blowing force

Read more
Silvent-Air Nozzles-shade_2

Fluid nozzles vs. air nozzles for compressed air

Read more
Silvent-hearing-protection-1

3 truths about noise and compressed air in industry

Read more
Cold-mill-Silvent

Minimize problems with emulsion in cold rolling mills with the use of compressed air

Read more

3 arrangements that improve safety when blowing with compressed air

Read more
working-environment-woman

Basic information about decibel (dB)

Read more
working-environment-tinnitus-hearing-loss.jpg

Decrease noise from air wands and valves for compressed air in industry

Read more
working-environment-air-in-bloodstream-fatal.jpg

What is sound?

Read more
Silvent-man-helmet-ear

Decrease the sound level in the manufacturing industry - 7 tips

Read more
silvent-world-wide-flags

Noise laws in the manufacturing industry

Read more
silvent-innovation-drawing.jpg

Choose the correct air nozzle for compressed air blowing

Read more
Man-with-Pro One-airgun-OSHA-gauge-1500pxl

How do you know if you are using a safe air blow gun?

Read more

When to use an air blow gun with an extension pipe

Read more
air-nozzle-compressed-air

Improve your blowing application with air nozzles for compressed air

Read more

Big saving possibilities when blowing with compressed air

Read more
Silvent-man-with-helmet

Risk of eye injuries, when blowing with an air blow gun

Read more

5 reasons to use air nozzles when blowing with compressed air

Read more

How to install an air blow gun

Read more

How often should you change pneumatic mufflers to avoid downtime?

Read more
Woman-in-Silvent-logistics

Pressure drop, a forgotten problem

Read more

Why should you use a flowmeter?

Read more
working-environment-injuries1

Why to use quiet air blow guns

Read more
Silvent-engineer-checking-nozzle

What does compressed air cost?

Read more
Silvent-man-in-laboratory

How to eliminate risk of non-compliance with OSHA regulation 1910.242(b)

Read more

Dangers of blowing with air blow guns for compressed air

Read more

What is compressed air and what is it used for?

Read more

What is tinnitus?

Read more